Electrolyzer Energy Consumption: DC Stack, AC System and Hydrogen Cost

2026-11-21

When comparing electrolyzers, electricity consumption is often one of the first specifications buyers examine. But does a figure of 4.3 kWh/Nm³ necessarily indicate better performance than 5.0 kWh/Nm³?

Only if both figures use comparable measurement boundaries and operating conditions.

One may describe the DC electricity supplied to the stack, while the other includes AC power conversion and auxiliary equipment. Hydrogen pressure, purity, measurement conditions and operating load may also differ.

Before comparing electricity consumption, align the electricity input boundary, the qualified hydrogen output boundary and the test conditions. This principle applies to AEM, PEM and alkaline water electrolysis.

1. DC Stack Consumption vs AC System Consumption

The electrolyzer stack performs the electrochemical conversion of water into hydrogen and oxygen. A working hydrogen production system also requires supporting equipment.

MetricWhat it measuresWhat buyers should check
DC stack consumptionDC electricity supplied to the stack divided by the corresponding hydrogen outputUsually excludes rectifier losses and auxiliary electricity
AC system consumptionAC electricity entering the agreed system boundary divided by qualified hydrogen outputConfirm whether water treatment, cooling, drying and purification are included
Electricity consumption at the hydrogen delivery boundaryElectricity required to deliver qualified hydrogen under specified conditionsMay also include compression and other project equipment

The term “system consumption” does not automatically mean that every supporting load is included. For example, an external chiller may be necessary for operation but excluded from the equipment’s stated electricity consumption.

The U.S. Department of Energy also distinguishes stack-level and system-level performance in its electrolysis targets. This distinction is useful for defining measurement boundaries; it does not make performance figures from different technologies directly interchangeable.

2. Why DC Stack Consumption Does Not Equal the Electricity Bill

Under simplified steady-state conditions:

AC system power ≈ DC stack power ÷ rectifier efficiency + auxiliary AC power

Consider an illustrative calculation:

  • Hydrogen production: 20 Nm³/h

  • DC stack consumption: 4.3 kWh/Nm³

  • Corresponding DC stack power: 86 kW

  • Assumed rectifier efficiency: 95%

  • Assumed auxiliary AC power: 5 kW

The resulting AC system power would be approximately 95.5 kW. If qualified hydrogen output remained at 20 Nm³/h, AC system consumption would be approximately 4.78 kWh/Nm³.

The rectifier efficiency, auxiliary power and resulting AC consumption in this example are assumptions for calculation purposes. They are not measured or guaranteed specifications for an AEMHY product.

If gas treatment, purging or off-specification operation reduces qualified hydrogen output, that reduction must also be reflected in the final calculation.

3. Converting kWh/Nm³ to kWh/kg

The unit kWh/Nm³ expresses electricity consumption per normal cubic metre of hydrogen. The unit kWh/kg expresses electricity consumption per kilogram.

Before converting, confirm the reference conditions used for “Nm³.” These conditions are not identical in every document.

This article uses dry hydrogen at 0°C and 101.325 kPa absolute pressure.

On this basis:

  • 1 Nm³ of hydrogen has a mass of approximately 0.0899 kg.

  • 1 kg of hydrogen occupies approximately 11.12 Nm³.

Therefore:

kWh/kg ≈ kWh/Nm³ × 11.12

For example, 4.3 kWh/Nm³ corresponds to approximately 47.8 kWh/kg.

This conversion changes the unit, not the measurement boundary. A DC stack figure remains a DC stack figure after conversion.

4. Calculating the Electricity Component of Hydrogen Cost

With a fixed electricity tariff and a clearly defined billing scope:

Electricity cost per unit of hydrogen = AC specific electricity consumption × electricity price

The following examples illustrate the calculation:

Assumed AC consumptionElectricity priceElectricity cost per Nm³Electricity cost per kg, approximately
4.8 kWh/Nm³US$0.05/kWhUS$0.24US$2.67
4.8 kWh/Nm³US$0.10/kWhUS$0.48US$5.34
5.2 kWh/Nm³US$0.05/kWhUS$0.26US$2.89
5.2 kWh/Nm³US$0.10/kWhUS$0.52US$5.78

These are calculation examples, not product quotations or project cost forecasts. Demand charges, capacity charges and other electricity fees are excluded.

Electricity cost is only one component of total hydrogen production cost. A project assessment should also include equipment investment, installation, water, maintenance, replacement parts, financing and any compression or storage included in the delivery scope.

For renewable-energy projects, electricity prices and operating availability may vary together. A realistic assessment should use the expected operating profile rather than applying the lowest available electricity price to the entire year.

5. Why Electricity Consumption Changes During Operation

Specific electricity consumption depends on operating conditions.

Load and current density. Changes in current density affect cell voltage and hydrogen production. Lower stack voltage at reduced load does not necessarily mean lower AC system consumption per unit of hydrogen, because auxiliary loads may not decrease proportionally.

Temperature, electrolyte and feedwater conditions. These influence conductivity, reaction behaviour, transport and long-term operation.

Hydrogen pressure and quality. Different delivery pressures, drying requirements and purity specifications may require different equipment and energy inputs.

Equipment condition and operating cycle. Start-up, standby, shutdown and performance degradation affect electricity consumption over time.

For project evaluation, a useful metric is:

Period-specific electricity consumption = Total electricity consumed within the agreed boundary ÷ Qualified hydrogen produced over the same period

The calculation should include agreed start-up, standby and auxiliary loads, rather than relying solely on a favourable steady-state test point.

6. Questions Buyers Should Ask

Before comparing technical proposals, confirm:

  1. Is electricity measured at the DC stack terminals or the AC system inlet?

  2. Are cooling, water treatment, drying, purification and compression included?

  3. Where is hydrogen output measured?

  4. Does the output represent dry hydrogen meeting the agreed quality specification?

  5. What temperature and absolute pressure define Nm³?

  6. What load, temperature, pressure and electrolyte conditions apply?

  7. Is the figure measured, estimated or guaranteed?

  8. Are part-load data and an acceptance-test method available?

If an efficiency percentage is provided, also confirm whether it uses the lower or higher heating value of hydrogen and whether it describes the stack or the complete system.

7. AEMHY’s Approach to Reporting Electricity Consumption

AEMHY currently provides a reference DC stack electricity consumption of 4.3 kWh/Nm³. This must not be presented as the AC consumption of a complete hydrogen production system or used on its own to promise a project’s hydrogen production cost.

The applicable model, operating point, test conditions and acceptance requirements should be defined in the relevant technical documentation and supply agreement.

Complete-system AC electricity consumption must be established for the selected rectifier, auxiliary equipment, gas treatment and operating conditions. AEMHY does not substitute its DC stack figure for an unconfirmed AC system value.

For AEM hydrogen projects, equipment selection should consider stack performance alongside system configuration, dynamic operation and maintenance requirements.

Contact Changzhou AEMHY Hydrogen Energy Technology Co., Ltd. to discuss your hydrogen demand, electricity supply, operating schedule and delivery requirements.

Website: https://www.aemhy.com/en/

Reference

U.S. Department of Energy — Technical Targets for Proton Exchange Membrane Electrolysis